Installing the Power
Supply for the
Centillion 100 Chassis
Part No. 893-00940-A
July 1996
Caution: Please read immediately
Inspect this power cord and determine if it provides the proper plug and is appropriately
certiļ¬ed for use with your electrical system. Immediately discard this cord if it is
inappropriate for your countryās electrical system and obtain the proper cord as required
by your national electrical codes or ordinances.
Refer to this productās technical documentation for detailed installation procedures to be
followed by qualiļ¬ed service personnel.
Vorsicht: Bitte sofort lesen
Sehen Sie nach, ob dieses Netzkabel Ć¼ber den richtigen Stecker verfĆ¼gt und fĆ¼r die
Verwendung in Ihrem Stromversogungsnetz zertiļ¬ziert ist. Falls dieses Kabel nicht fĆ¼r
das Stromversorgungsnetz in Ihrem Land geeignet ist, darf es nicht verwendet werden.
Besorgen Sie sich ein Kabel, das die Vorschriften der Zulassungsbehƶrden in Ihrem Land
erfĆ¼llt.
Die technische Dokumentation dieses Produkts enthƤlt ausfĆ¼hrliche
Installationsanweisungen, die nur von qualiļ¬ziertem Kundendienstpersonal ausgefĆ¼hrt
werden dĆ¼rfen.
Attention: Lisez ceci immƩdiatement
Examinez ce cordon d'alimentation pour dĆ©terminer s'il dispose de la ļ¬che appropriĆ©e et
s'il est bien agrƩƩ pour utilisation sur votre installation Ʃlectrique. DƩbarrassez-vous en
immĆ©diatement s'il ne convient pas Ć l'utilisation sur le secteur Ć©lectrique en usage dans
votre pays et procurez-vous un cordon conforme Ć la rĆ©glementation nationale en vigueur.
Reportez-vous Ć la documentation technique de ce produit pour obtenir des instructions
dĆ©taillĆ©es d'installation, destinĆ©es Ć un technicien qualiļ¬Ć©.
893-00940-A
1
Installing the Power Supply for the Centillion 100 Chassis
Attenzione: Leggere attentamente
Controllare questo cavo di alimentazione, veriļ¬carne il collegamento con la presa
appropriata nonchĆ© la certiļ¬cazione per l'uso nell'impianto elettrico posseduto. Non
utilizzare assolutamente in caso tale cavo non sia adatto al sistema elettrico del paese in
cui viene utilizzato e richiederne un altro certiļ¬cato dall'ente nazionale di fornitura
elettrica.
Per le procedure di installazione che devono essere seguite dal personale di servizio,
consultare questa documentazione tecnica del prodotto.
Advertencia: SĆrvase leer inmediatamente
Inspeccione este cable de alimentaciĆ³n elĆ©ctrica y determine si viene con el enchufe
apropiado y estĆ” debidamente certiļ¬cado para el uso con su sistema elĆ©ctrico. Si no
cumple con los reglamentos del sistema elĆ©ctrico de su paĆs, despĆ³jese de este cable de
alimentaciĆ³n inmediatamente y obtenga el cable requerido, segĆŗn las ordenanzas y
cĆ³digos elĆ©ctricos nacionales.
Reļ¬Ć©rase a la documentaciĆ³n tĆ©cnica de este producto para recibir informaciĆ³n detallada
sobre los procedimientos que el personal caliļ¬cado de reparaciones deberĆ” seguir
2
893-00940-A
Adding a Power Supply
Adding a Power Supply
CAUTION: Only qualiļ¬ed technicians should install this equipment.
Required tool: Flat-tip screwdriver
7265
1. Use the ļ¬at-tip screwdriver to loosen the two screws; then remove the ļ¬ller
panel from the chassis.
7266
2. Align the new power supply with the slot guides and slide the power supply
into the chassis.
893-00940-A
3
Installing the Power Supply for the Centillion 100 Chassis
7267
3. Push down on the power supply handle to align the screws and tighten the
screws to between 2 and 4 inch-pounds of torque. Do not overtighten.
LEDs
Power
switch
7268
4. Connect the power cord to the power supply and then to the wall. (See power
cord caution on page 1.)
5. Turn on the power. Verify that the upper (green) LED lights.
For detailed instructions, refer to Installation and Reference for the Centillion 100
Chassis.
4
893-00940-A
Replacing a Power Supply
Replacing a Power Supply
CAUTION: Only qualiļ¬ed technicians should replace this equipment.
Required tool: Flat-tip screwdriver
Power
switch
7269
1. Turn off the power to the faulty power supply and unplug the cord.
7270
2. Use the ļ¬at-tip screwdriver to loosen the two screws; then remove the power
supply from the chassis.
893-00940-A
5
Installing the Power Supply for the Centillion 100 Chassis
7271
3. Align the new power supply with the slot guides and slide it into the chassis.
7272
4. Push down on the power supply handle to align the screws and tighten the
screws to between 2 and 4 inch-pounds of torque. Do not overtighten.
6
893-00940-A
Replacing a Power Supply
7273
5. Connect the power cord to the power supply and then to the wall. (See power
cord caution on page 1.)
LEDs
Power
switch
7273.1
6. Turn on the power. Verify that the upper (green) LED lights.
For detailed instructions, refer to Installation and Reference for the Centillion 100
Chassis.
893-00940-A
7
Installing the Power Supply for the Centillion 100 Chassis
Speciļ¬cations
The following table provides the speciļ¬cations for the power supply.
Line frequency:
Volt Amperes rating:
Input voltage:
47 to 440 Hz
Electrical
250 VA
90 to 132 V or 180 to 264 V
5/2.5 A
Input current rating:
Fuses:
Internal; not accessible to user
One power supply:
850 BTU/hr. maximum
900 BTU/hr. maximum
Thermal rating
Physical
Multiple power supplies:
Dimensions:
2.4 in. (H) x 6.5 in. (W) x 12 in. (D)
6.1 cm (H) x 16.5 cm (W) x 30.5 cm (D)
Handle projection:
Weight:
1 in. (2.54 cm)
1.6 lb (0.725 kg)
8
893-00940-A
|
Miller Electric Welder and DS 74D16 User Manual
NCR Scanner 7837 User Manual
NEC Car Video System 2070WNX V User Manual
NEC IP Phone 4 User Manual
Oki Printer 14ex User Manual
Omega Engineering Marine Instruments DPG10L User Manual
Omron Thermometer 9063366 4A User Manual
Onkyo Stereo Receiver TX NR737 User Manual
Onkyo Stereo System SR308 User Manual
Panasonic Vacuum Cleaner MCCG917 User Manual